Willex Manual Hose Crimping Machine — Shop-Grade Crimping, Anywhere Without Power

The DZW-51CSD is a hand-pump hydraulic hose crimping machine that brings 1650 kN of crimping force to jobsites and workshops without an electrical supply. Covering a 1/4"–2" hose range with ten included die sets, it is the portable choice for mobile hose service, remote maintenance, and space-conscious fabrication.



Where a powered crimper cannot reach, the DZW-51CSD does. By replacing the electric motor with a lever-actuated hydraulic pump, Willex has engineered a machine that still delivers 1650 kN of crimping force — enough to form consistent, leak-free couplings on high-pressure braided and spiral hoses — while remaining fully independent of mains power. Its compact 550 × 550 × 500 mm frame and 165 kg net weight fit into a service vehicle or a one-bay workshop, and the ten included die sets (Nos. 15–63, with optional sizes available) cover the most common 1/4"–2" assemblies straight out of the crate.


Detailed Parameters

Crimping Range1/4"-2"Crimping Force1650 KN
Maximum Open Diameter113mmMax.Opening±30mm
Work Efficiency10pcs/hMotor PowerHand Pump
Machine Size550*550*500mmPacking Size715*610*700mm
Net Weight165KgGross Weight190Kg

Die Parameter

Dies No

Range(mm)Length(mm)

∅15

15-1960

∅19

19-23
60

∅23

23-2660

∅26

26-3160

∅31

31-3670

∅36

36-4170

∅41

41-4770

∅47

47-5580

∅55

55-6380

∅63

63-9380

Key Advantages

True Site Independence

Runs fully on a hand-pumped hydraulic circuit, needing no mains power, compressed air, or external unit — ready for remote sites, service trucks, and field repair.

Operator-Neutral Consistency

The relief valve stops the crimp automatically at a fixed pressure, so every closure hits the same diameter regardless of who pumps.

Rapid Die Changeover

Ten included dies swap in seconds without tools, letting one technician move between hose sizes mid-job.

Minimal Maintenance Load

No motor, contacts, sensors, or valves to service — just oil checks and seal inspection, so downtime stays low.

Rigid, Self-Contained Footprint

The closed bench frame stays planted through full-force cycles and bolts straight onto a truck or small workshop floor.

Inherent Overload Protection

The relief valve caps the crimp before dies or couplings can be crushed, extending tool life and protecting the operator.



Product Gallery


Frequently Asked Questions

Q:Since this is a hand-pump machine, how do I know every crimp lands on the same diameter — won't different operators pull the lever with different force?

The hydraulic circuit reaches a fixed pressure relief point and stops automatically, so die closure stays consistent from operator to operator regardless of lever effort.

Q:With 1650 kN of crimping force, can it really handle 4-wire spiral hose at the 2-inch end, or is that rating only realistic for smaller braided hoses?

The 1650 kN rating covers the full 1/4"–2" range and is suitable for standard 1-and-2-wire braided as well as 4-wire spiral assemblies within their working-pressure limits.

Q:Is the listed 10 pieces per hour a realistic sustained output, or just a best-case figure for one repeated hose size?

Ten pieces per hour is the sustained shop-floor average including normal die changes; on a single repeated size, operators typically run noticeably faster.

Q:Are the ten included dies proprietary to Willex, or can I source matching dies from other suppliers later?

The die pockets follow the common industry profile, and the ten included numbers plus optional sizes cover your most-used couplings without locking you into a single supplier.

Q:Without an electric motor, what routine maintenance does the hydraulic power unit actually require?

Maintenance stays simple — check the oil level, top up with standard ISO 46 anti-wear hydraulic oil, and inspect the seal set annually, with no brushes, contacts, or electronics to service.

Q:At 165 kg net weight, is this truly portable, or just a compact bench machine that happens to be moved once?

The 550 × 550 × 500 mm frame is engineered for two-person carry or a pallet jack, which is why mobile service operators mount it permanently in hose-service trucks rather than relocating it daily.


Ready to Optimize Your Hydraulic Assembly Line?

Contact Us



Send a Message

If you are interested in our products, you can choose to leave your information here, and we will be in touch with you shortly.

  • *
  • *
  • *
  • *

If you are interested in our products, you can choose to leave your information here, and we will be in touch with you shortly.